HEATIT 12FT Water Pipe Heat Tape | 7W/ft 120V Constant Wattage Heating Cable for Pipes

• CSA & ETL Certified for Superior Safety — CSA and ETL certifications are trusted safety marks in North America, ensuring compliance with strict industry standards. Our self-regulating heating cable is fully CSA and ETL certified, from end to end, guaranteeing top performance and reliability. The plug is UL certified for extra protection. Always choose a fully certified heating cable—just a plug certification isn’t enough. True safety comes with complete certification.
• For Water-Filled Pipes Only — 𝙐𝙨𝙚 𝙛𝙤𝙧 𝙬𝙖𝙩𝙚𝙧 𝙛𝙞𝙡𝙡𝙚𝙙 𝙥𝙡𝙖𝙨𝙩𝙞𝙘 (𝙞𝙣𝙘𝙡𝙪𝙙𝙞𝙣𝙜 𝙋𝙀𝙓) 𝙤𝙧 𝙢𝙚𝙩𝙖𝙡 𝙥𝙞𝙥𝙚𝙨. 𝙉𝙤𝙩 𝙪𝙨𝙚 𝙛𝙤𝙧 𝙖𝙣𝙮𝙩𝙝𝙞𝙣𝙜 𝙚𝙡𝙨𝙚, 𝙡𝙞𝙠𝙚 𝙚𝙢𝙥𝙩𝙮 𝙬𝙖𝙩𝙚𝙧 𝙥𝙞𝙥𝙚𝙨, 𝙛𝙪𝙚𝙡 𝙡𝙞𝙣𝙚𝙨, 𝙝𝙤𝙨𝙚𝙨, 𝙜𝙪𝙩𝙩𝙚𝙧𝙨, 𝙨𝙩𝙚𝙖𝙢 𝙡𝙞𝙣𝙚𝙨 𝙖𝙣𝙙 𝙨𝙤 𝙤𝙣. Comes with a two-year limited warranty for long-term reliability. If not completely satisfied with HEATIT heating cable, please don't hesitate to contact our service at any time.
• Pre-Assembled & Easy Installation — Includes a grounded plug with an indicator light, a built-in thermostat, and clear instructions. Operates at 120V, 7W/ft, with an automatic thermostat that turns on at 37°F and off at 50°F. Maximum 1/2 in fiberglass insulation was used over the heating cable for lower temperature protection. No crossing. No spiral. No overlap itself. Only straight.
• Test Before Installation for Safety — Before installation, uncoil the cable, plug it in, and place the thermostat in an ice bucket. When the temperature drops below 37°F, the cable will activate and warm up slightly. Avoid prolonged testing to prevent overheating.
• Durable & Reliable Protection — Features 100% screen rate with aluminum foil and tinned copper braid, industrial-grade heat shrink tubing, and tough XLPE insulation. Must be installed straight (no crossing, spiraling, or overlapping). Backed by USD 2 million in product liability insurance.

• Uncoil and Inspect — Uncoil the heat tape, check for damage, and ensure the cable is straight without crossing or spiraling. Keep away from combustible materials.
• Connect & Test — Plug into a grounded outlet, turn on, and verify indicator light. Test in ice bucket to confirm activation below 37°F, avoiding prolonged testing.
• Install on Pipes — Lay the cable straight over water-filled pipes up to 1.5 inches diameter, ensuring thermostat contact. Secure with non-metallic fasteners, no overlaps.
• Final Check & Power — Ensure the cable runs straight, no crossing or spiraling. Cover with fiberglass insulation if needed. Keep combustible materials 1/2 inch away.

Typical situations where HEATIT 12FT Water Pipe Heat Tape | 7W/ft 120V Constant Wattage Heating Cable for Pipes helps — illustrative scenarios, not customer reviews.